Solar motor

This is a basically a brush-less, solar powered electric motor. it operates on the principal of the correct coils being charged biased on where the panels are in relation to a single light source. its not very powerful, so it has magnetic bearings to reduce friction.

My Youtube Chanell

Just like my Lego rubber band page, I have a youtube chanell that I havent uploaded anything new to latley.
However, it has a few cool gizmos and what not from a few years ago on it.

http://www.youtube.com/user/pafrig

Lego Rubber Band Guns

4 or 5 years ago I used to make a LOT of lego rubber band guns. I posted them all on this site a while ago.

http://www.mocpages.com/home.php/4774

Drift Trikes

Last spring my friend and I started making drift trikes. If you dont know what drift trikes are, there pretty much just "big wheels" for foolish teenagers. Instead of me typing a bunch of stuff to describe it completley and making us all go to sleep, heres a link.

http://www.youtube.com/watch?v=w8UGk6TP0Lg

Anyways, we built some! the first started with a cut up bike that was pulled out of a trash pile, with some 3 inch abs pipe wheels mounted on cut up lawnmower rims.

notice how the frame is kinked, we thought we should change the rake for better drifting, but it ended up dropping the entire bike too low and the frame scraped when the wheel was turned too far. eventually, a second kink was added.

one run, the bearings in the rear wheels got hot enough to melt the plastic hubs. cannibalized skateboard to the rescue!

the skate wheels worked till we started loosing bearings.. so we moved on! the next wheels are covered in acetal, a hard brittle plastic. the wheels were actually mass produced for a FIRST robotics challenge, so they didn't take too big of a bite out of my wallet.

                                                                       On the first run we hit some gravel roads doing 30+ mph and totally destroyed the new wheels. big rocks just hit the brittle plastic and took big chunks out of it. conveniently, they have an outside diameter of 6 inches so I just sleeved them with 6" Pvc pipe. the Pipe is attached with countersunk drywall screws.
                                                                          After all this, it was decided it was time for a version #2! this one is much smaller and made from a bmx bike rather than a mountain bike. a fundamental difference between the first and second trike was that the first had independley spinning wheels while the second had a live axle. The live axle was made of a peice of 5/8 inch rebar spun down to size on a improvised lathe. (drill and angle grinder)

                                            the second trike is in the back. the rear portion is made of a bent pair of forks from a crashed three wheeler with a split rim from a scooter acting as the bearing blocks. the rear tires are 6" pvc mounted on lawnmower rims.

here it is in action! The front wheel is changed out because the first one had a bent rim. the new one is from a minibike.

Steam Engine Post #1

Im making a steam engine in my Jewlery class, heres the fly wheel. all the other peices are in the shop, but heres a picture of the fly-wheel

its all made from bent copper sheet.

Underwater ROV

This is an ROV ("Remotely Operated Vehicle") that I made out of PVC and assorted hardware. Underwater Rovs are used for search and rescue, underwater repair, and anything else where a robot can be substituted  for a human in a sub-par "this place sucks, why am I here doing this?" type of environment. My ROV is small and more like a toy than a tool, but hey.

Its on a 45' cat five tether, and controlled via 4 double pull double throw switches. The rov itself has six motors. with 4 pairs of wire in the cat 5 and six motors, there had to be some sneaky wiring done. The motors are synced in pairs of 3. for example, if the "left" switch is thrown, the left motor comes on. the right switch, the right motor. however, when both switches are thrown in the same direction a 3rd motor comes on. I really didnt think of it at the time, but it probolay dosent help with power consumption as 1 motor probolay maxes out the 24 gauge wire.. haha. theres also some leds that come on in different colors depending on direction of thrust. heres the controller. its a 4" PVC end cap. The two tanks on the top of the the wing create near-neutral buoyancy.

heres some more pictures of the ROV

Gokart

This Is a gokart that I built last year. It started off during the summer of 2010 when I took summer school classes at the vocational school. I had welding in the morning and Small engines in the afternoon. In our small engines class the project was to put a gokart together out of a kit so that the school could sell it for fundraising or something. Halfway through the course, I had what i thought was an excused absence of a week (at the school, if you miss more than 3 days, they drop you). anyways, i came back after a week long marine biology escapade and was told that i was essintaily expelled. bummer. Having nothing better to do, iIwalked the 2 miles in the rain over to the schools main office. I spoke with the higher powers at work, and was re-enrolled on the premise that I would be auditing the class.

The small engines teacher said that there were no more gokart kits to put together, ("thank goodness" I thought to myself) so he gave me the project of making an old gokart new again. the poor thing had been sketichily extended and ruthlesly crashed, so I spent a week in welding making it stronger and closer to true. I then put a 1950's snowmachine engine on it. It worked great for about 10 minutes of burnouts and wheelies. The fun came to an end after a half inch shaft going into a lawnmower transmission that I had rigged up sheared. bummer. again. at the end of the course, the small engines teacher came up to me at the end of class and said, "well Dewane, you dont get a grade, but you get a gokart. get that hunk of junk out of here" anyways, I got a free gokart and engine and whatnot!  Ive looked for pictures of it in this stage, but cant find any.

At home, I rebuilt it all. the snowmachine engine got replaced by a 125cc, 4 speed transmission three wheeler engine. It also got bigger tires and an aluminum gas tank. Heres some photos and videos!

My Hi-Tech Paint Booth

My Hi-Tech frame straghtiner.

Done!

Driving around and popping wheelies!

Sadly, we took it off some jumps this summer and broke the axle. Its yet to be fixed!

Metal Art

Copper Bird

I built this out of some copper wire that I stripped. I think it was originally supposed to be a flower or something, but creativity happens

Railroad Spike Animals

I have a friend that used to be into making metal art. a few summers ago, he asked for my help getting this large piece of steel into his truck.I gladly agreed to help, and the next thing I knew, we were in a railroad yard with a large piece of half inch plate and five gallon buckets full of railroad spikes in the back of the truck. Cool!... right? Well apparently (according to the renta-cop) we didn't exactly have the permission to be there. long story short, we were told to put the plate back, but to take all the used spikes that we wanted. that summer, there was a plethora of railroad spike based art made, but this is all I could find around the house.




 



Globe Dude
I started taking a jewelry class this year in school, and this is one of the things that I have made. It started as just a brass ball, then it turned into a globe, then it turned into a goodie-box, then there was a copper-wire man to hold it. I made it by cutting out two brass circles, pounding those into hemispheres with dapping cubes. I then painted on the continents with tar, and submerged the globe in nitric acid. the acid dissolved the copper in the brass that wasn't covered with tar, essentially raising the continents. Finally, I put a band on the inside to hold the two halves together, yet still be able to open it.

Birthday Bird

I built this with my friends little brother for his sisters birthday. The bird is made of bicycle spokes, its supported by a piece of bike chain welded in place, and it all rests on a cut out of Alaska.

Lego Robot

I used to be really into Lego robotics. this is a robot from the 2007/2008 Power Puzzle challenge. It started out as something simple that was supposed to be kept simple, but when I started tinkering with pneumatics and pto's, things just got out of hand and I ended up with this.

The drive train consisted of 3:1 reduction to extra wide tires. a rotation sensor was used on each wheel to position the robot during its autonomous period. There's a 1:3 ratio driving the sensors (the blue box things) to attain the speed range that the sensors worked best in.

Many Implements were powered, but you were limited to three motors. One motor powered a lifting arm and a a PTO (power take off, like on a tractor) that powered implements. in later years, a clutch separated the worm drive box from everything else so that the PTO could spin infinitely.

In the end, murphys law came into effect even after working bugs out. The robot was able to consistently able to score perfect scores on the practice table, but never at competition (it did come close though!)